Are there any safety concerns when using lock washers?

Nov 20, 2026Leave a message

If you’ve ever stood in a workshop, watching a mechanic tighten a bolt on a heavy piece of machinery, or assembled a bookshelf that wobbly even after extra turns with a screwdriver, you’ve likely encountered lock washers—small, unassuming parts that make a huge difference. For a lock washer supplier, I get asked all the time: “Are there any safety concerns when using these things?” It’s a fair question, because lock washers aren’t one-size-fits-all, and using them incorrectly can lead to issues that range from annoying wiggles to serious, even dangerous, failures. Let’s break this down, using real-world examples, science, and the lessons I’ve learned working with these parts for years.

First, let’s get back to basics: what lock washers do. Their whole job is to stop bolts and nuts from loosening over time—especially in applications that see vibration, temperature changes, or heavy loads. Think of a truck’s wheel bolts, a construction crane’s arm joints, or even a factory conveyor belt’s drive system. Without lock washers, constant vibration can make bolts back out gradually, leading to misalignment, part damage, or, in the worst cases, catastrophic breaks. But here’s the catch: safety issues with lock washers don’t come from the parts themselves—they come from how they’re chosen, installed, and matched to the job. Let’s start with the most common mistake I see, and it’s a big one: mismatching the lock washer type to the application.

Not all lock washers are created equal. Two of the most popular options in our catalog are zinc plated lock washers and stainless steel lock washers, and each has a specific sweet spot. Zinc plated lock washers are cost-effective and offer good corrosion resistance for indoor or mild outdoor use, like shelving units, HVAC systems, or garage machinery. But push them into a high-moisture, chemical-heavy environment—like a marine dock or a food processing plant where they’re exposed to washdowns with acidic cleaners—and the zinc plating can wear off quickly, leaving the underlying steel vulnerable to rust. A rusted lock washer loses its tension, so it can no longer hold the bolt tight. I once heard from a manufacturing client who used zinc plated lock washers on their outdoor equipment storage racks. Within two years, the washers rusted through, bolts loosened in a heavy wind storm, and a whole section of the rack collapsed—luckily, no one was hurt, but it cost them tens of thousands in replacement parts and downtime. That’s a safety concern from picking the wrong washer, plain and simple.

Stainless steel lock washers, on the other hand, hold up to corrosion far better. The grade 304 stainless we supply, for example, resists rust in saltwater, mild acids, and high humidity, making it ideal for marine, food and beverage, or coastal construction projects. But even stainless steel has a limit. Use a standard helical spring stainless lock washer in an application with extremely high temperatures—like a furnace exhaust manifold or a boiler— and the spring’s temper breaks down. The metal loses its elasticity, so it can’t generate the friction needed to keep the bolt tight. I’ve had a client in the metalworking industry make exactly that mistake. They used standard stainless lock washers on their furnace’s bolted joints, and after six months of constant high heat, the washers flattened out. The bolts loosened, leading to a small exhaust leak that could have turned into a dangerous carbon monoxide buildup if it had gone unnoticed. That’s another safety concern: material limitations that aren’t checked against the application’s operating conditions.

Next up: installation errors. This is one of the most avoidable safety issues, but it’s shockingly common. The biggest mistake here is putting the lock washer on backwards. Let’s talk about how a helical spring lock washer works: it has a split that creates two bent tabs. When you tighten the nut or bolt, the tabs dig into the surface of the part you’re fastening and the head of the bolt or nut. That digging creates friction and prevents rotation. If you put the washer on backwards, the tabs face away from the surface—so instead of digging in, they slide. I saw this firsthand with a local construction crew working on a pedestrian bridge. They installed the lock washers backwards on the handrail bolts. Within a few months, constant foot traffic and wind vibration made the bolts loosen. A few people reported wobbly handrails, and the crew had to shut down part of the bridge for repairs. It was a completely preventable mistake, but it happens all the time because people don’t take the 10 seconds to check the washer’s orientation.

Another installation error: over-tightening or under-tightening. Lock washers rely on a specific amount of tension to work. If you under-tighten, the washer doesn’t compress enough to create the friction needed to resist vibration. If you over-tighten, you can actually flatten the washer so much that it loses all its spring action. I remember a client who was assembling heavy-duty farm equipment. They over-tightened all the bolts with lock washers because they thought “tighter is safer.” After a few harvest seasons, the bolts started snapping. When they called me for a replacement, I examined the old washers—they were completely flattened, with no remaining spring tension. The over-tightening not only ruined the washers but also put excess stress on the bolts, leading to their failure. The correct torque, by the way, is usually marked on the application’s specs, and lock washers work best when installed to that exact spec, not more or less.

Then there’s the issue of using the wrong size lock washer. This might seem trivial, but using a washer that’s too small means it doesn’t cover the entire bolt’s shank, so it can’t distribute the clamping force evenly. A washer that’s too big can shift around, not sit flat against the part, and fail to create the required friction. I once had a hobbyist customer come to me complaining that his new garden tractor’s wheels kept falling off. He’d bought lock washers from a big-box store that were labeled “universal” for 1/2-inch bolts, but they were actually 9/16-inch, too big for his 1/2-inch bolt. The washers shifted when he drove the tractor, and over time, the wheels worked loose. It took him a couple of hours to replace them with the right-sized washers, but he said he was lucky he didn’t get hurt while mowing the lawn.

Wait, what about split lock washers vs. other types, like tooth lock washers? Sometimes the material itself isn’t the issue, but the design of the washer. Tooth lock washers, for example, have sharp external or internal teeth that dig into surfaces. They work great on soft metals like aluminum or wood, but if you use them on a hard steel surface, the teeth can’t bite in, so they don’t provide any locking force. I had a client in the automotive industry who used external tooth lock washers on their steel engine blocks. The teeth couldn’t penetrate the hard steel, so the washers slid around, and the bolts in the valve train loosened. It took them a few tries to switch to helical spring washers, which create tension without needing to bite into the hard surface. That’s another safety concern: picking the wrong design for the surface material.

There’s also a less talked-about issue: compatibility with other parts. Lock washers might not play well with certain coatings or surface finishes. For example, if you’re using a zinc plated lock washer on a part that’s been coated with a soft paint or powder coat, the sharp edges of the washer can tear through the coating. Over time, that tear leaves the underlying metal exposed to corrosion, and the missing coating also makes it harder for the washer to create friction. I had a furniture manufacturer tell me about their custom office chairs—they used lock washers on the leg brackets, but the washers tore through the chair’s black powder coat, leading to rust spots after a year of use. They switched to washers with rounded edges, which don’t tear the coating, and the problem went away. It’s a small detail, but it matters for long-term safety.

Now, let’s talk about what I, as a lock washer supplier, do to help customers avoid these safety concerns. First, we don’t just send a box of washers and hope for the best. Our team works with customers to match the right washer type, material, and size to their specific application. If someone’s working on a outdoor sign that’ll be exposed to rain and snow, we’ll recommend stainless steel instead of zinc. If they’re building a conveyor belt in a factory, we’ll specify the correct torque and even give them guidelines on installation to avoid backwards washers. We also provide educational resources—like blog posts and installation guides—that walk through the common mistakes we see every day.

But even with all that, sometimes safety issues pop up. That’s why it’s so important for anyone using lock washers to do regular inspections. For critical applications—like heavy machinery, construction, or automotive parts—inspecting the washers (and bolts) every few months is non-negotiable. Look for signs of rust, flattening, or shifting. If a washer is rusted through, replace it immediately. If it’s flattened, that means it’s lost its tension, so it can’t do its job. I always tell customers: don’t wait for a failure to do something. Catching a problem early is way safer and cheaper than dealing with the consequences.

Let me wrap this up with a few key takeaways, because that’s what I want people to remember. Lock washers are not a set-it-and-forget-it part. The safety concerns when using them don’t come from the washers themselves, but from how you choose, install, and maintain them. Pick the right material: zinc plated lock washers for mild indoor/outdoor use, stainless steel lock washers for corrosive or high-temperature environments. Install them correctly: the right orientation, the right size, and the right torque. Don’t over-tighten or under-tighten, and make sure the design matches the surface you’re fastening. And always inspect, especially for critical applications.

At the end of the day, my job as a lock washer supplier isn’t just to sell parts—it’s to make sure those parts are used safely and effectively. If you’re working on a project and aren’t sure which lock washer is right for you, or you have questions about installation, reach out to our team. We’ve worked with everything from small hobby projects to large industrial builds, and we can help you avoid the mistakes that lead to safety issues. Don’t cut corners on lock washers—they’re small, but they’re one of the most important parts for keeping people and equipment safe.

Zinc Plated Lock Washer suppliersStainless Steel Lock Washer suppliers

References

  1. Shigley, J. E., & Mischke, C. R. (2001). Standard Handbook of Machine Design (3rd ed.). McGraw-Hill.
  2. Machinery’s Handbook (31st ed.). Industrial Press, 2020.
  3. Bickford, J. H., & Nassar, S. (2012). Handbook of Bolts and Bolted Joints (2nd ed.). CRC Press.
  4. Corrosion Resistance of Stainless Steels. (2019). Nickel Institute.
  5. Vibration-Induced Loosening of Bolted Joints. (2018). Journal of Mechanical Design, Vol. 140, No. 10.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry