From GB to ANSI and DIN - choosing the right nut for every joint
A practical reference for engineers, buyers and importers who specify hexagon nuts. It explains how the three dominant standards systems define a nut, where they quietly disagree, and how to turn a joint requirement into one unambiguous part number.
Cover: hexagon nuts on a machined steel surface.
Published at [https://www.chinaboltnut.com/] · November 2026
Applicable standards: GB/T, ISO, DIN, ASME B18.2.2, ASTM A563
1. Why the Nut Decides Whether the Joint Holds
In a bolted joint the nut is rarely the most expensive item and almost always the least specified - which is precisely why it decides so many failures.
A bolted joint is not a bolt with a nut attached to it. It is a closed system of three components - bolt, nut and clamped parts - with three possible ways to fail: the bolt breaks, the thread strips, or the joint loses its clamp load. The nut takes part in all three. It sets how much thread is engaged, how the load is spread across the bearing face, and how much of the bolt's strength can actually be used.
In practice, the nut is where the specification usually stops. A purchase order reads "M10 hex nut, zinc plated". That sentence describes at least four different products: a GB/T 6170 class 8 nut, a DIN 934 class 8 nut with a 17 mm across-flats, a thin GB/T 6172.1 nut, and a nylon-insert lock nut. They differ in height, wrench size, proof load and behaviour under vibration. Choosing between them is an engineering decision, not a purchasing formality.
This guide sets out how the three dominant systems - GB/T (aligned with ISO), DIN and ANSI/ASME - define a nut, where they diverge, and how to convert a joint requirement into a part number that cannot be misunderstood.
A nut is not a commodity. It is the component that decides whether the bolt is allowed to do its job.
2. Inside the Joint: What a Nut Actually Does
2.1 Preload is the product
A tightened joint holds because the bolt is stretched and the clamped parts are compressed. That tension - preload - is the real output of the assembly, and the nut is the mechanism that generates and stores it. The nut therefore has to do two things well: transmit torque without galling or seizing, and carry the resulting load without yielding.
This is why nut strength is expressed as proof load rather than tensile strength. A nut is not pulled apart; it is loaded by the bolt thread pushing outward on the nut thread and by the bearing face pressing against the clamped part. ISO 898-2 therefore specifies a proof load stress for each property class, verified by a proof load test in which the nut must withstand the load without thread stripping or permanent distortion.
2.2 Thread engagement: the 0.8D rule
Load travels from bolt to nut through the engaged threads. If engagement is too short, the first few threads carry almost everything and strip. The widely used rule of thumb is a minimum engagement of 0.8 times the nominal diameter for a steel nut on a steel bolt - roughly eight full threads for a class 8 nut. Below that, stripping becomes the governing failure mode and the bolt's strength is wasted.
Engagement is set by nut height plus any washer, and it must be checked on the drawing rather than assumed. In tapped aluminium or cast iron the required engagement is longer; in soft plastics a metal insert is the only reliable answer.

Figure 1. Thread engagement is where the load lives. Only the engaged threads and the bearing face carry clamp load; everything below the last engaged thread is dead length.
2.3 The three height styles
ISO 898-2 and its Chinese counterpart GB/T 3098.2 sort nuts into three styles by height rather than by width across flats: style 0 (thin nuts), style 1 (regular hex nuts) and style 2 (high nuts). Height determines how many threads engage and how the load spreads. A thin nut is a locking or space-saving element, not a substitute for a regular nut in a loaded joint. A high nut is used where the bolt is stronger than a standard nut can support, or where the joint must survive severe vibration and thermal cycling.

Figure 2. Regular, heavy and thin hex nuts. Width across flats changes very little between them; height - and therefore engaged thread length - is the real difference.
3. Three Standards, Three Engineering Traditions
The world's nut specifications grew out of three separate industrial histories and they still do not fully agree. Understanding what each system optimises for prevents the most common import and export error: assuming that a nut with the right thread will fit.
3.1 The GB/T and ISO metric family
China's fastener standards are now largely adoptions of ISO standards, which makes GB/T the most internationally portable metric system. The core products are:
GB/T 6170-2015, Hexagon regular nuts (style 1) - the default metric hex nut, M1.6 to M64, property classes 6, 8 and 10 plus stainless and non-ferrous designations, product grades A and B.
GB/T 6175-2016, Hexagon high nuts (style 2) - taller nuts for higher load and tougher service.
GB/T 41, Hexagon nuts, product grade C - the rougher, lower-precision nut for general structural and construction work.
GB/T 6172.1, Hexagon thin nuts - the thin series for jam-nut and space-limited applications.
GB/T 889.1, Prevailing torque hexagon nuts with non-metallic insert - the nylon-insert lock nut.
GB/T 6184, Prevailing torque all-metal hexagon nuts - the all-metal lock nut for higher temperatures.
GB/T 3098.2-2015, Mechanical properties - nuts - the Chinese adoption of ISO 898-2:2012.
The dimensional parents are ISO 4032 (style 1), ISO 4033 (style 2), ISO 4035 (thin) and ISO 7040 and ISO 7042 for prevailing torque nuts. Because GB/T follows ISO with a lag, the current ISO editions can be newer than the GB/T text: ISO 4032 was revised in 2023 and ISO 898-2 in 2022. When a customer drawing cites ISO rather than GB/T, check the edition before quoting.
3.2 The DIN legacy
DIN standards were the working language of European industry long before ISO harmonised them, and they remain in wide use in Germany, in Central and Eastern Europe, and in older machinery drawings everywhere. The key point is that DIN 934 - the classic hex nut - is not dimensionally identical to ISO 4032. The difference is small in absolute terms and large in practice.

A 17 mm spanner does not fit an ISO M10 nut. In a mixed consignment, this alone can stop an assembly line. DIN also offers a family of special-purpose nuts that remain common on European drawings: DIN 936 (thin nut), DIN 439 (thin hexagon nut with chamfer), DIN 985 (nylon-insert lock nut), DIN 980 (all-metal prevailing torque nut) and DIN 935 (slotted castle nut for split-pin locking).
DIN 934 has been formally superseded by DIN EN ISO 4032, but parts are still produced and stocked to the old DIN dimensions. Ask the supplier which drawing the parts were actually made to: "DIN 934" in a catalogue sometimes means no more than "a hex nut".
3.3 The ANSI/ASME inch family
North America never metricated its fastener system, and its nuts follow a different logic: dimensions from ASME B18.2.2, materials from ASTM specifications.
ASME B18.2.2-2015 covers machine screw nuts, hex nuts, square nuts, hex flange nuts and coupling nuts in the inch series. Two families matter most: the regular hex nut, and the heavy hex nut, which is larger across flats and thicker and is the standard choice for structural steelwork. Threads follow ASME B1.1: UNC (coarse) and UNF (fine) - 1/2-13 UNC, 5/8-11 UNC, 3/4-10 UNC and so on.
Material grades come from ASTM A563, which covers carbon and alloy steel nuts in grades A, B, C, D and DH. Grade C and DH heavy hex nuts are the normal partners for ASTM A325 and A490 structural bolts. Marking is mandatory for most grades, and the marking tells you what the carton does not: the grade and the manufacturer.
The practical trap is the inch–metric boundary. 1/2-13 UNC is 12.700 mm, not 12 mm. A 12 mm metric nut will not run onto a 1/2 inch bolt, yet the two look almost identical in a parts bin and are frequently confused on mixed-language drawings.
4. Five Dimensional Details That Cause Field Problems
4.1 Across-flats
As Table 1 shows, the flat-to-flat dimension is the one that decides whether the assembly station can tighten the joint at all. Where a plant runs both DIN and ISO parts, colour-code the bins; the cost of one mis-sorted box is a stopped line.
4.2 Height and thread engagement
A thin nut substituted for a regular nut reduces engaged thread length, and the joint strips before the bolt reaches its proof load. Match the nut style to the calculation, not to what happens to be on the shelf.
4.3 Thread form and pitch
Metric coarse (M10×1.5) and inch UNC are both 60-degree threads but they are not interchangeable. Fine-pitch metric nuts (M10×1.25) will start on a coarse bolt for a turn or two and then bind - the most common cause of "bad thread" complaints that are actually wrong-part complaints.
4.4 Bearing face and chamfer
The bearing face transmits preload into the clamped part. A nut with a chamfer on the bearing side, or one used against a damaged washer face, reduces contact area and causes embedment and preload loss. For high-strength joints in aluminium or thin sheet, a flange nut or a hardened washer is not decoration.
4.5 Marking
The property class and the manufacturer's mark are stamped on the bearing face or on a flat. Unmarked nuts cannot be verified and cannot be traced; in structural work they are normally non-conforming. If a supplier ships unmarked nuts, a certificate is the only evidence you will ever have - and that is not enough.
5. Property Class: Match the Nut to the Bolt
The rule is simple and is often inverted in practice: the nut should be at least as strong as the bolt, and in most designs slightly stronger, so that if the joint is overloaded the bolt stretches visibly rather than the nut stripping silently. The conventional pairing puts the nut one property class below the bolt.

Class 12 nuts are not always stocked and are often unnecessary: a class 10 nut on a 12.9 bolt is normal practice where the bolt's own margin is large. What is not acceptable is a class 8 nut on a 10.9 bolt - a pairing that appears very often in low-cost kits.
For stainless steel, ISO 3506-2 governs and the designations are different: A2 (304 type) and A4 (316 type), in property classes 50, 70 and 80. GB/T 6170 permits A2-50, A2-70, A4-50 and A4-70. Stainless nuts gall readily, so a lubricant is advisable; and A4-70 should never be assumed to equal a class 8 steel nut, because its capacity falls sharply at elevated temperature.
In the inch system the same idea runs through ASTM A563 grades, which are matched to bolt grades rather than to property classes, together with the rule that structural nuts be heavy hex.
6. Nut Types by Function
Every nut shape in a catalogue exists because one specific load, locking or assembly problem had to be solved. Choosing by function rather than by habit is the fastest way to reduce both cost and field failures.


Figure 3. A functional specimen set: standard, heavy, thin, nylon-insert lock, flange, slotted, coupling and square nuts.
A note on locking. Nylon-insert nuts are the most practical answer to vibration in most industrial joints, but the insert limits continuous service temperature to roughly 120 °C. Above that, all-metal prevailing torque nuts, or a properly specified thread-locking compound, are the options. Split-pin locking through a castle nut is the only method that gives a positive, visible, inspectable lock - which is why it survives in safety-critical linkages.
7. Material and Finish
7.1 Material
Carbon steel covers the great majority of nuts: classes 6 and 8 from medium carbon steel, classes 10 and 12 from alloy steel with heat treatment. Stainless A2 and A4 cover corrosion resistance and food or pharmaceutical environments, at roughly half the load capacity of a comparable steel nut. Brass and aluminium nuts appear in electrical, instrumentation and lightweight assemblies.
7.2 Finish

The most expensive mistake in this table is ordering hot-dip galvanized nuts to standard thread tolerance. The zinc layer consumes thread clearance and the nut will not run onto the bolt. Galvanized nuts must be tapped oversize and matched with galvanized bolts of the same system, so that the coating on the bolt consumes the rest of the clearance.
8. Selecting by Application
Structural steel: heavy hex, ASTM A563 grade C or DH, hot-dip galvanized, with A325 or A490 bolts; confirm that the nut is heavy hex and marked.
Automotive and transport: flange nuts and nylon-insert lock nuts, classes 8 or 10, with a defined prevailing torque after repeated reuse.
General industrial machinery: GB/T 6170 or ISO 4032 class 8, zinc plated, is normally the correct baseline. Do not over-specify into class 10 unless the calculation asks for it.
Offshore, marine, chemical: A4 (316) stainless, or hot-dip galvanized plus a coating system; A2 is not adequate for chloride exposure.
High temperature: all-metal lock nuts or plain nuts with a suitable anti-seize compound; nylon inserts are ruled out.
Food, pharmaceutical, washdown: A4 stainless, or a coated system with documented food-contact approval.

Figure 4. Heavy hex nuts on a structural connection, hot-dip galvanized. In structural work the governing documents are dimensional (ASME B18.2.2) and material (ASTM A563), not a single property class.
9. A Seven-Step Selection Workflow
Applied in order, these seven steps turn a vague requirement into a part number that a supplier can quote, a inspector can verify and a line can install.
Step 1 Fix the joint function. Load, vibration, temperature, corrosion class, and whether the joint is safety-critical.
Step 2 Identify the bolt. Thread system (metric or inch), property class, coating and whether it is a stud or a bolt.
Step 3 Choose the nut style from the calculation. Regular, heavy, thin or locking - driven by engagement and load, not by stock.
Step 4 Match the property class. Nut class at least equal to the bolt class, conventionally one step below.
Step 5 Confirm engagement. At least 0.8D of engaged thread in steel, more in light alloys; check washer and insert thickness.
Step 6 Set the finish and the thread tolerance that goes with it. Hot-dip galvanizing requires oversize tapping; electroplating on class 10 and 12 requires baking.
Step 7 Write the part number in full. "GB/T 6170 M10 class 8, zinc plated per ISO 4042" is a specification. "M10 nut, zinc" is a hope.
10. Six Pitfalls Worth Memorising
1. Mixing DIN and ISO nuts in one assembly. The across-flats differ and the spanner does not fit.
2. Substituting thin nuts for regular ones to save space. The joint loses engaged thread and strips before the bolt is loaded.
3. Under-matching the nut class. A class 8 nut on a 10.9 bolt fails first, and the bolt is blamed.
4. Ordering galvanized nuts to standard thread tolerance. The zinc layer closes the thread clearance and nothing assembles.
5. Using nylon-insert nuts above their temperature limit. A melted or extruded insert is a misapplication, not a supplier defect.
6. Accepting unmarked nuts in structural work. An unmarked nut is an unverifiable nut, however good the certificate.
11. Quick Reference

12. Standards Cited
Standards are revised on their own timetable. Verify the current edition before a drawing is released; the list below reflects the editions available at the time of writing.
· GB/T 41, Hexagon nuts, product grade C
· GB/T 6170-2015, Hexagon regular nuts (style 1)
· GB/T 6172.1, Hexagon thin nuts
· GB/T 6175-2016, Hexagon high nuts (style 2)
· GB/T 889.1, Prevailing torque hexagon nuts with non-metallic insert
· GB/T 6184, Prevailing torque all-metal hexagon nuts
· GB/T 3098.2-2015, Mechanical properties of fasteners - nuts
· ISO 4032:2023, Hexagon regular nuts (style 1)
· ISO 4033, Hexagon high nuts (style 2)
· ISO 4035, Hexagon thin nuts, chamfered
· ISO 7040, Prevailing torque hexagon nuts with non-metallic insert
· ISO 7042, Prevailing torque all-metal hexagon nuts
· ISO 898-2:2022, Mechanical properties - nuts with specified property classes
· ISO 3506-2, Stainless steel fasteners - nuts
· ISO 4042, Electroplated coating systems
· ISO 10683, Zinc flake coating systems
· ISO 10684, Hot dip galvanized coatings
· DIN 934, Hexagon nuts
· DIN 936, Hexagon thin nuts
· DIN 439, Hexagon thin nuts with chamfer
· DIN 985, Prevailing torque hexagon nuts with non-metallic insert
· DIN 980, Prevailing torque all-metal hexagon nuts
· DIN 935, Slotted castle nuts
· ASME B18.2.2-2015, Nuts for general applications (inch series)
· ASME B1.1, Unified inch screw threads
· ASTM A563, Carbon and alloy steel nuts
· ASTM A325 / A490, Structural bolts
· ASTM F594, Stainless steel nuts




