Jihao Fasteners Wraps Up Three Days At The 19th Linyi Agricultural Machinery Expo

Nov 10, 2026 Leave a message

 

 

Press Release | Handan Yongnian Jihao Fasteners Manufacturing Co., Ltd. | 19 November 2026

 

 

      LINYI, Shandong - From 16 to 18 November 2026, Handan Yongnian Jihao Fasteners Manufacturing Co., Ltd. received visitors at Booth F208, Hall 3 of the Linyi International Convention and Exhibition Centre (Economic Development Zone), during the 19th China (Linyi) Agricultural Machinery and Accessories Expo. The show occupies more than 80,000 square metres of exhibition space, hosts over 2,000 booths and expects more than 80,000 professional visitors, with shuttle service for buyers arriving from outside the city.

news-1080-1920

Figure 1 | The Jihao Fasteners booth (Hall 3, Booth F208) during the 19th Linyi Agricultural Machinery Expo, 16–18 November 2026.

 

What We Showed

      Our display was built around the parts that actually fail first on working machinery: the linkage, hitching and locking hardware of farm equipment and tipper trailers. Rather than a catalogue wall, the table carried sample sets that visitors could pick up, measure and compare.

      U-bolts in square and round form, with matching nuts, spring washers and flat washers, sit at the centre of the range, supported by lifting eye bolts, double-eye clevis bolts and double-eye pull rings used at drawbar and hitching points.

      For locking and adjustment we brought slotted and castle nuts, heavy-duty slotted nuts, round lock nuts and colour-zinc slotted nuts, paired with plain, zinc-plated and colour-zinc clevis pins, together with R-clips, cotter pins and circlips that keep a pin from working loose in service.

      The range is completed by tipper-truck fittings, wedge bolts, hook bolts and fork-end bolts, which are produced to drawing rather than to a fixed catalogue number.

news-1440-902

Figure 2 | Sample sets of non-standard fasteners for agricultural machinery and tipper trailers on the display table.

Where These Parts Are Used

      The expo covers agricultural machinery, plant protection equipment, garden machinery, water-saving irrigation, power machinery and machinery parts, and our products follow the same application map.

      In practice the parts go into three groups of joints. Suspension and axle assemblies take the U-bolts, with the square type clamping leaf springs and the round type fixing axle saddles. Hitching and towing assemblies take the double-eye pull rings, clevis bolts and pull pins, where the load changes direction and the joint has to pivot rather than simply hold. Adjustment and locking positions take the slotted nuts, round lock nuts and locking pins, where a nut has to stay where it was set through vibration and repeated field use.

      On tipper trucks and trailers, the same families appear at tailgate hinges, sideboard locks, drawbars and stabiliser legs, which is why we group them under tipper-truck fittings in our own product list.

Materials and Finishes

      Standard production uses carbon steel in property class 4.8 and 8.8, with class 10.9 available on request where the working load requires it. Dimensions and thread specifications are confirmed against the customer drawing or against the sample supplied, and we quote both metric coarse and fine thread where the application calls for it.

Surface treatment is chosen by the environment, not by habit. Clear zinc plating suits indoor and dry service, colour zinc gives a thicker, more decorative coating for parts that are handled and stored outdoors, hot-dip galvanising is used for structural sizes that stay outside for years, and Dacromet is offered where a coating without hydrogen-embrittlement risk is needed for high-strength parts. Every option is confirmed in writing before production, because the coating decision affects both the fit of the thread and the service life of the joint.

news-2166-1279

Figure 3 | Large-size U-bolts, eye bolts, clevis bolts and clevis pins in zinc and colour-zinc finish.

What Buyers Asked About

      Conversations at the booth followed a consistent pattern. Buyers arrived with a worn part in hand or with a drawing on a phone, and the first question was usually whether we could match the dimension exactly rather than whether we could supply something similar. The second was the surface treatment and how it would hold up in the field. The third was minimum order quantity, tooling cost and delivery time for a first batch.

      These are the questions we are set up to answer. New parts are quoted from a drawing or a physical sample, existing tooling is reused where the geometry allows, and batch sizes are agreed against the customer's actual consumption rather than a fixed figure. Buyers who visited the booth left with a sample set and a written specification for their own part.

About Jihao Fasteners

      Handan Yongnian Jihao Fasteners Manufacturing Co., Ltd. is a manufacturer based in Yongnian District, Handan, Hebei, the established fastener production base in northern China. The company produces non-standard bolts, special fasteners and custom hardware for agricultural machinery, engineering vehicles and trailers, and works to customer drawings and samples under OEM and ODM arrangements. Export enquiries are handled in English, with specifications, packing and shipping terms confirmed in writing before each order is released.

news-1080-2152

Figure 4 | Exhibition notice: Hall 3, Booth F208, 16–18 November 2026, Linyi International Convention and Exhibition Centre.

Contact

      Handan Yongnian Jihao Fasteners Manufacturing Co., Ltd.

      Mobile / WhatsApp: +86 186 0330 8322 | +86 138 3102 4888

      For drawings, samples and quotations, please send your part specification directly to the numbers above.

 

 

Contact now

 

 

Send Inquiry

whatsapp

Phone

E-mail

Inquiry